AMX NMX-DEC-N3322D – 4K60 H.26x/Dante AV-H Decoder

Description

AMX SVSI NMX-DEC-N3322D decoders can decode the highest quality 4K60 H.26x and Dante AV-H video streams output by AMX N3300 encoders or other Dante AV-H cameras, digital signage players, or software.

In addition to supporting HDCP content from N3300 encoders, they also feature enhanced support for high-security networks.

NMX-DEC-N3322D decoders support Dante AV-H, a standard for AVoIP devices created to allow for the interoperability of multiple devices on the network. With Dante AV-H, NMX-DEC-N3322D decoders are compatible with Dante Studio, a suite of software tools for PC, that allows you to monitor or bring video directly into UC, recording, production, or streaming applications without the need for additional hardware. Dante Controller handles all device routing, naming and configuration, while Dante Domain Manager provides IT-level management over device organization, user access, multiple subnet coordination and complete audit logs for every endpoint and user.

Compatible encoders include AMX N3300 Series encoders, N3000 Series encoders, the NMX-WP-N3510 Windowing Processor, and other Dante AV-H encoders. Additionally, the NMX-DEC-N3322D can decode an H.264 stream generated by N2600S Series encoders.

Moving 4K60 video to or from the Cloud just became a lot easier with AMX SVSI N3300 Series Encoders and Decoders.

• High-quality 4K60 H.26x Decoding
• Audinate® Dante AV-H support
• Dante Audio
• Support for high security networks
• PoE+ powered with low-power mode for energy savings =+= Technical Specification
VIDEO
Digital Video Input
Network video over Ethernet via RJ45 port
Digital Video Output
HDMI 2.0
Formats
HDMI 2.0, HDCP 2.2 content protection support
Progressive Input Resolutions
Supports most common HD resolutions up to 4K60 4:4:4
Output Resolutions
720p, 1080p, 4K60 or input resolution if scaler is disabled
Output Scaling
Scaling adds one frame of latency (17ms at 60fps)
Colour Space
4:4:4, YUV
LocalPlay/HostPlay
8 playlists
Network Video Recording
H26x stream is compatible so long as the source is not HDCP.
H264/H265 VIDEO
Stream Video Input
Up to 4K60 4:4:4
Frame Rate
50 or 60 Hz
Profiles
H264: Baseline (BP), main (MP), high (HiP) / H265: main (MP)
Bitrate Range
500 Kbps to 32 Mpbs
Rate Control
VBR CBR
Streaming Protocols
RTP, RTSP, RTMP, RTMP/S, SRTP, Dante AV-H
AUDIO
Input Signal Types
Network audio over ethernet
Output Signal Types
Embedded audio on HDMI or Analogue Audio Output
HDMI Audio Formats
8ch PCM
Analogue Audio Format
Stereo 2-channel
Audio Breakaway
Supported
LATENCY
Latency
End to end video Latency: 110 ms
COMMUNICATIONS
Ethernet
10/100/1000 Mbps, auto-negotiating, auto-sensing, full/half duplex, DHCP and Static IP
HDMI
HDCP, EDID management
PORTS
+12V 2A
One 12 Volt DC power input
P0 PoE+
8-wire RJ45 port. 10/100/1000 Mbps 10/100/1000Base-T auto sensing gigabit Ethernet switch port. Provides network connection, network AV video, and power to the Encoders and Decoders PoE+ power.
P1
8-wire RJ45 port. 10/100/1000 Mbps 10/100/1000Base-T auto sensing gigabit Ethernet switch port. Provides network connection, network AV video.
IR IN (front panel)
3-pin terminal Phoenix connector. Provides Infrared (IR) input only and passes signal back to connected decoder (33-60 kHz; typically, 39 kHz) IR receiver is necessary (not included)
IR OUT
2-pin terminal Phoenix connector. Provides Infrared (IR) output only (33-60 kHz; typically, 39 kHz). Emitter is necessary (not included).
RS232
3-pin terminal Phoenix connector which provides a serial control interface. Full duplex communication. Available terminal speed settings: 1200-115200 baud rate.
AUDIO
5-pin terminal Phoenix connector which provides user- selectable balanced/unbalanced output. Dedicated audio input.
HDMI OUT
HDMI video output (passive pass-through from HDMI IN only)
CONTROLS AND INDICATORS – FRONT PANEL
RESET Button
Recessed pushbutton. Press to initiate a ‘warm restart’ causing the processor to reset, but not lose power. A reset does NOT affect the current settings.
ID Button
Recessed pushbutton. Press to send a notification out on the network to identify the unit (the notification causes a pop-up dialog in N-Able and N-Command). Holding the button for 30 seconds and releasing will cause the device to return to factory configuration.
POWER LED
On solid (green) when operating power is supplied (via PoE or local power supply).
STATUS LED
On flashing (green) when there is software activity.
STREAM LED
On (green) when the unit is streaming video.